Arrow NW108 Instruction Manual Page 1

Model No. EN108-A HM108-A MN108-A NP108 NW108-A PD108-A SA108-A VN108-A 697.68538-AOwner's Manual & Assembly Instructions A01

It is important that the entire floor frame be anchored after the building is erected.Below are recommended ways of anchoring. Anchoring Down The Buil

11Remove from bag of screwsand save for the last step67293Weather Stripping (1)5971Roof Beam Bracket (4)66382Lower Door Guide (4)66183Roof Trim Cap(2

Parts List A1212Assembly Part Part Quantity CheckKey No. Number Description in Carton List 1 3719 Door Handle Brace 2 2 9364 Wall Pa

13Assembly by Key No.A13191613202122272323323232322212221212121212262626263344111110171731991511158828292931313130252555181830252588242172423232323231

The front floor frame is made up ofthree pieces. The side floor framesand the rear floor frame are made upof two pieces. The holes in thesepieces will

Step 2A1515● Parts Needed For ●Frame AssembliesThe main frame pieces reinforce thewalls. These pieces will later be in-stalled in the center and at th

16The roof beams join the two gablesand support the roof panels. The mainroof beam is made up of four piecesoverlapped back to back at the cen-ter. Th

17NOTE:Door Track Splice (painted part)Step 4A17● Parts Needed For ●Door Track Assembly●●●●● 6403 Door Track Splice (1)●●●●● 9366 Door Track (2)66769S

●●●●● Front Floor Assembly (1)●●●●● Side Floor Assembly (2)●●●●● Rear Floor Assembly (1)● Parts Needed For ●Floor FrameStep 5A18The floor frame must b

1 Position a corner panel at thecorner of the floor frame as shown.The widest part of each corner panelmust be placed along the side of thebuilding f

2Owner's ManualBefore beginning construction, check local building codes regarding footings, locationand other requirements. Study and understand

The main frame pieces give rigidity tothe side walls and provide a surfacefor attaching the gables which sup-port the roof.1 Fasten the rear wall ang

Step 8A21● Parts Needed For ●Wall Panels●●●●● 9364 Wall Panel (4)●●●●● 8995 Wall Panel (4)The wall panels come in two widths.Each wall panel has a cri

●●●●● 9900 Door Jamb (2)●●●●● 9365 Front Wall Channel (2)● Parts Needed For ●Front Channel/Door JambStep 9A22The door jambs reinforce the dooropening

23The gables go on top of the front andrear walls to support the roof beams.NOTEThe gables are packed nestedtogether and might be mistakenas one piece

● Parts Needed For ●Gables/BracesStep 11A24●●●●● Left Gable Assemblies (2)●●●●● Right Gable Assemblies (2)●●●●● 6635 Gable Brace (2)241 Lift and fast

25Step 12A25● Parts Needed For ●Roof Beams●●●●● Main Roof Beam (1)●●●●● Single Roof Beam (2)1 Spread the two halves of the mainroof beam and fasten th

26Step 13A26● Parts Needed For ●Right Roof Panel●●●●● 8468 Right Roof Panel (1)Installing the roof panels is best donewith a step ladder. Begin insta

1 Install a left roof panel at the leftrear and right front corner of the roof.Install a right roof panel at the leftfront corner of the roof.3 Instal

28Step 15A28● Parts Needed For ●Ridge Caps & Panels●●●●● 8840 Ridge Cap (1)●●●●● 7483 Roof Panel (2)●●●●● 8486 Ridge Cap (1)1 Install the first ri

1 Attach the right and left side rooftrim to the lower end of the roof pan-els on each side of the building usingscrews at each panel overlap.NOTEA si

3Selecting and Preparing Your Site: Before assembly, you will want to decide ona location for your building. The best location is a level area with go

30●●●●● 3719 Door Handle Brace (2)●●●●● 10489 Right and Left Doors (2)●●●●● 10497 Horizontal Door Brace (4)●●●●● 9355 Vertical Door Brace (2)● Par

31Step 18A31● Parts Needed For ●Door Installation & Adjustment●●●●● Right Door Assembly (1)●●●●● Left Door Assembly (1)1 From inside the building,

AnchoringAnchor your building at this time.Floor FrameIf you have purchased a Floor Frame Kit you need to install it at this time.32Anchoring and Floo

SOME FACTS ABOUT RUSTRusting is a natural oxidizing process that occurswhen bare metal is exposed to moisture. Problemareas include screw holes, unfin

4Safety precautions are important to follow throughout the construction of your building.•Care must be taken when handling variouspieces of your build

Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immedia

ACCESSORIES... A6 WEB6* Some drilling required to fit buildings without mid-wall bracing.Model No. SS404• Makes 8" to 12" (20,3-30,5 c

THIS PAGEWASLEFTBLANKINTENTIONALLY7

THIS PAGEWA SLEFTBLANKINTENTIONALLY8

The Base For Your Building9FRONT(DOOR)FRONT(DOOR)Base A09Note: Finished Slab dimensions, with lumber removed.OPTION 1: ARROW FLOOR FRAME KIT: (Ord